Bissell Deep Clean Advanced Cleaner (Instructions)
BISSELL Deep Clean Advanced is a concentrated carpet-cleaning formula for compatible BISSELL upright carpet extractors, not a mop cleaner. Vacuum first, then fill the machine’s water and formula compartments to their marked lines, using warm tap water as directed. Clean with controlled passes, extract moisture, and let the carpet dry fully before allowing traffic.
Carpet can look clean on top while soil remains deeper in the pile. That is why a formula made for an extractor works differently from a floor-cleaning solution: the machine applies solution to carpet and then pulls much of it back into a recovery tank. Using the formula in a mop or on a hard floor skips that extraction step.
I treat the bottle label, machine manual, and carpet-care instructions as a set. The bottle identifies the product; the machine markings control the fill amounts; and the carpet maker’s directions help determine whether the treatment is suitable. If any instructions differ, pause and check the current product label and manuals before cleaning.
Surface Preparation and Carpet-Cleaning Chemistry
BISSELL Deep Clean Advanced is a 2X-concentrated carpet formula intended for compatible carpet-cleaning machines. “Concentrated” means it is designed to be used with water in the machine’s specified setup, not poured straight onto carpet. Its verified pH is not established here, so check the current bottle label or product safety data sheet for that information.
Before starting, confirm that the carpet-care instructions allow machine extraction and that your BISSELL cleaner accepts this formula. Test the mixed solution in a hidden spot, following the product and machine directions. Let the test area dry, then check for color change or other unwanted effects before treating a larger area.
Vacuum the carpet thoroughly. This removes loose grit and debris that would otherwise mix with the cleaning solution. Pick up larger objects by hand, and address stains only with a treatment approved for your carpet and compatible with the machine process. Do not assume that more formula will improve cleaning; excess solution can be hard to remove.
A carpet extractor is designed to recover moisture, but it cannot make the carpet instantly dry. Too much liquid, repeated wet passes, or slow drying can leave carpet and its backing overly wet. If you suspect water has reached the backing or subfloor, stop applying solution and focus on extraction and drying.
IICRC S100 is a reference for cleaning textile floor coverings. It is not a substitute for your carpet manufacturer’s care directions or the machine manual. IICRC S300 concerns upholstery cleaning, so it is not the governing carpet-cleaning standard.
Before you clean: check compatibility, test a hidden area, vacuum well, and plan for ventilation and drying.
Extractor Setup, Fill Lines, and Tool Selection
The clean-water and formula compartments are meant to be filled according to the marks and instructions for your specific machine. There is no universal water-to-cleaner ratio to substitute for those markings. Use the designated carpet-cleaning tool and the machine’s appropriate setting, rather than adapting a hard-floor or handheld setup without checking the manual.
Fill the tanks by their labels
Empty and rinse the tanks first if they contain old solution or residue. Add warm tap water as directed by the cleaner’s manual, stopping at the marked water line. Add the formula only to its designated compartment and only to the marked level. Do not pour concentrate directly onto carpet or exceed either tank’s fill marks.
“Warm” does not mean boiling or very hot. Follow the machine’s temperature guidance, and do not heat water beyond what the manual allows. If the tank markings are unclear, find the model-specific instructions rather than estimating a ratio from another BISSELL machine or a different product bottle.
| Setup detail | Use this approach | Avoid |
|---|---|---|
| Water amount | Follow the clean-water tank’s fill line | Guessing a volume or exceeding the line |
| Formula amount | Use the designated compartment and its marked line | Pouring concentrate onto carpet |
| Water temperature | Use warm tap water as the manual directs | Boiling or very hot water |
| Cleaning tool | Use the compatible carpet tool specified for the machine | Substituting an unapproved tool |
| Product fit | Check the bottle and machine instructions | Assuming every cleaner accepts every formula |
Choose the carpet setting and tool
Install the carpet-cleaning tool named in the manual and select the setting recommended for the task. Some machines have more than one mode or attachment; their names and operation differ by model. Do not rely on a setting from a different machine. If the cleaner has a separate rinse option, use it only as its instructions direct.
Keep the tank seated correctly and confirm that the recovery tank is installed and ready to collect liquid. If the machine does not dispense solution or recover it as expected, stop and check its setup and troubleshooting instructions. Continuing with a malfunctioning extractor can leave too much liquid in the carpet.
Next step: make a small test pass in an inconspicuous area, then confirm that the machine dispenses and recovers solution as expected.
Controlled Cleaning Passes and Drying
Controlled passes mean moving the extractor steadily and following the machine’s instructions for solution application and recovery. The aim is to clean the carpet without repeatedly soaking the same area. Drying time is not fixed: carpet construction, machine performance, airflow, and room humidity all affect how long it takes.
Start in a corner or another less visible section. Use the machine’s stated pass technique and pace; do not invent a universal number of wet or dry strokes, since machine instructions vary. Work in manageable sections and overlap only as directed. Avoid pausing with solution flowing over one spot or repeatedly applying solution to an area that is already wet.
If your cleaner has a separate suction-only or rinse function, use it only as described in that model’s manual. Do not add extra formula to address a slow-cleaning area. If a patch still looks dirty after the instructed process, check for a specific stain or soil issue and follow an appropriate treatment procedure rather than increasing concentration.
Illustrative troubleshooting examples
These are practical examples, not reported customer cases.
- The carpet feels wetter than expected: Stop adding solution. Check that the recovery tank is seated, the nozzle is clear, and the machine is operating as instructed. Use the prescribed extraction steps, then improve airflow.
- A cleaned area dries with visible residue: Review whether the tanks were filled correctly and whether the formula was used only in its designated compartment. Follow the machine manual for any rinse or additional extraction step. Do not apply more concentrate.
- The carpet’s backing or floor below seems wet: Stop cleaning that area. Extract moisture only as the machine allows, increase airflow, and avoid further solution application. If moisture damage or odor becomes a concern, seek advice from a qualified carpet-care professional.
Ventilate the room and increase airflow with suitable fans or open windows when conditions allow. Keep people and pets off the carpet until it is dry. There is no single dry-time guarantee for every home, so check the carpet rather than relying on a fixed number of hours.
Excess moisture can affect carpet backing and the floor beneath it. If you notice signs that the backing or subfloor has become wet, do not continue wet cleaning. Correct the extraction and drying process before considering another pass.
Key point: use the machine’s pass method, avoid repeated wetting, and keep traffic off the carpet until it has dried.
Machine, Brush, and Mop-Head Care
After cleaning, care for the extractor according to its manual so leftover formula and soil do not remain in the tanks or cleaning parts. Empty and rinse the tanks, then clean the nozzle and brushes as directed. A mop head is not part of this carpet-extraction method, and the formula should not be transferred to a mop.
Switch off and unplug the machine before cleaning parts if the manual requires it. Empty the recovery tank promptly, since it holds extracted dirty water. Rinse removable tanks and let them dry as instructed. Check the nozzle and brush area for collected fibers or debris, and remove buildup using the method approved for your model.
Do not use fabric softener on microfiber components or add unapproved cleaners to the machine. If a part is difficult to remove, or you are unsure whether it can be rinsed, check the machine instructions instead of forcing it. Proper cleaning after use also makes it easier to notice a blocked nozzle or worn component before the next job.
| After-use task | Why it matters | What to follow |
|---|---|---|
| Empty the recovery tank | Removes collected dirty water | Machine manual |
| Rinse the tanks | Clears remaining solution or soil | Tank-care instructions |
| Check the nozzle and brushes | Helps identify buildup that may affect operation | Model-specific cleaning steps |
| Dry stored parts as directed | Avoids storing them wet when the manual calls for drying | Manufacturer directions |
Finish by: rinsing and checking the machine parts named in the manual, then store the cleaner as directed.
Conclusion
The safest, most consistent method is to treat the label and machine markings as the formula guide, not to guess a dilution. Prepare the carpet, use warm tap water as directed, fill each compartment to its marked line, and make controlled extraction passes. Stop if the carpet becomes overly wet, then focus on recovery and drying.
Frequently asked questions
Can I use BISSELL Deep Clean Advanced in any carpet cleaner?
No. Check the product label and your machine manual to confirm compatibility before use.
What is the water-to-cleaner ratio?
Use the water and formula fill lines on your specific machine. Do not substitute a guessed universal ratio.
Can I pour the concentrate directly onto carpet?
No. Put the formula only in the designated machine compartment and follow its marked fill line.
Should I use hot or boiling water?
Use warm tap water as directed by the machine. Do not use boiling or very hot water.
Can I use this formula in a mop?
No. It is a carpet-extraction formula, not a mop solution or a hard-floor cleaner.
Can I use it on hardwood, laminate, tile, stone, or vinyl flooring?
Do not use it on those surfaces. It is intended for compatible carpet-cleaning machines, and it is not verified here for hard floors.
How many passes should I make?
Follow the pass method in your machine manual. There is no single pass count that applies to every model and carpet.
How long will the carpet take to dry?
Drying varies with the carpet, machine, airflow, and humidity. Ventilate the room and keep traffic off until the carpet is dry.
What should I do if the carpet is too wet?
Stop applying solution, check the machine setup, and use its instructed extraction steps. Increase airflow and do not continue if the backing or subfloor seems wet.
Does the formula have a neutral pH?
A verified pH is not established here. Check the current product label or safety data sheet rather than assuming a value.
(This article was written by one of our staff writers, Justin Bennett. Visit our Meet the Team page.)
